Home > Error Code > Triton Traverse Error Codes

Triton Traverse Error Codes

Contents

If the error persist, possible causes may be the modem or main board assembly. 193 Baud rate setting for electronic journal failed 1. Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 126 Diverter moved to reject position during dispense Inspect for a note jam at the diverter. Test the dispenser by completing several test dispenses. 4. The upper RJ-45 port is used for downloading software only. this contact form

Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 117 Timeout waiting for note to divert   118 Exit sensor blocked on start of dispense or Make sure the shelf that the dispenser is mounted on is level and seated at all four corners. 3 Make sure the diverter moves freely. 4. This occurs when the last cassette has been taken out of service. Ensure the reject bin is empty, or that there is enough room for the rejects and test notes to fall into the reject bin. https://www.tritonatm.com/service_and_support/error_code_lookup/index.php

Triton Error Code 244

Release the printer locking screw. Verify that all sensors are operation correctly. If the test dispenses are completed normally, and the return code are correct, clear all errors and place the cash dispenser in operation. 5. Verify correct operation with a live transaction. 3.

  1. If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly. 3.
  2. Clear the error. 3.
  3. Make sure it is connected to CN1 on the printer control board.
  4. Sign in to add this to Watch Later Add to Loading playlists... 800.498.5795 New!
  5. This is a timing wheel or timing wheel sensor error.. 1.
  6. It the status clears, place the cash dispenser in service.
  7. Verify the blue lever on the left side of the printer in the print position. 3.

Purge the dispenser using the purge command from diagnostic menu. 2. Note, if the EJ is connected to the load port of the 9100 main board, permanent damage may result. 2. Keyword search will match on all words; a single keyword will; provide the maximum amount of results. Atm Error Codes List Power down the ATM in the proper sequence.

If this does not correct the problem, verify that the paper low sensor is correctly attached to the paper bracket and that the cable between the paper low paper feed assembly Inspect electronic journal to dispenser communication cable for damage. Purge the dispenser. http://www.atmdepot.com/triton-atm-error-codes/ Clean as needed with soft brush and vacuum cleaner. 2.

If these actions have no effect on dispenser operation, replace the dispenser mechanism. Triton Error Code 101 If you suspect SPED tamper or Error code 205, see the corrective action for Error Code 205. 192 Communication error 1. If the status clears and the return code are normal place the cash dispenser in service. Probable cause for this error is a faulty or uncalibrated double detect module, or a jammed currency in the double detect.1.

Triton 9100 Error Codes

Verify that all access panels are closed and secured. check this link right here now Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 110 Trailing edge time- out at exit. 1. Triton Error Code 244 Clear the error. 2. Triton Error 236 It may be necessary to replace the dispenser. 200 Dispenser fed extra note into stacker This status appears when the count at the exit can not be guaranteed. 1.

If the error clears, put the cash dispenser in service. 5. weblink Make sure the connectors are seated securely on the main board and on the electronic journal. 4. Inspect electronic journal to dispenser communication cable for damage. Make sure the connectors are seated securely on the main board and on the electronic journal. 2. Triton Atm Error Code 151

The cables may be defective. 3. If the cables are undamaged, the main board or electronic journal may be defective 158 Format command to electronic journal failed 1. Check the operation of the diverter solenoid. 3. navigate here Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 103 Thickness sensor unstable Enter the diagnostic function and complete the “learn note thickness” command.

If the error persists, replace the dispensing mechanism. Triton Traverse Error Code 917 Clear all errors and test the dispenser by completing several TEST DISPENSES. Make sure that the exit sensor is clean and operation correctly. 3.

Clear the error.

Inspect the cable supplying DC power from the power supply to the printer. Inspect for jammed currency at the Diverter. Make sure they are seated at the printer control board and not damaged. 6. Triton Error Code 616 Place cassettes in service. 157 Erase command to electronic journal failed 1.

Home 1-866-787- 4866 | e-Mail | About | Contact Us | Login Products News Services & Support Partner Programs Service & Support Training Programs Warranty Programs Warranty Registration Legacy Products When this is done, the terminal will operate normally until it is completely out of paper. Verify that the DC voltages to the dispenser are correct. his comment is here Inspect the cables connected to CN2, CN3, CN4, and CN5.

Clear all errors and test the dispenser with a live transaction. Sign in to add this video to a playlist. ATM ATOM 547 views 1:52 Blowing up a Triton 9100 ATM. ATMMoneyMachine 57 views 0:35 Buggy software at ATM & state of software development and testing - Duration: 1:32.

Remove jammed currency. 2.