Home > Error Code > Triton Reported Error Code 33 Feed Failure

Triton Reported Error Code 33 Feed Failure

Contents

Inspect the Electronic Journal to make sure it is the correct part number. If the cables are undamaged, the main board or electronic journal may be defective 155 Electronic journal modify record failure 1. Verify that the telephone line is operational. 3. Inspect electronic journal to dispenser communication cable for damage. this contact form

Please try the request again. Replenish the paper. If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly. 3. If the error persists, replace the dispensing mechanism. http://www.accessatm.com/service/atm-error-codes/triton-error-codes/

Atm Error Codes List

Remove any jammed notes.2. Start by verify your communications settings and external TCP-IP equipment. 2. If the problem persists, replace the dispensing mechanism. 135 Feed sensor blocked as reported by status check 1. This error is not displayed at the Cash Dispenser.

  1. Make sure the connectors are seated securely on the main board and on the electronic journal. 2.
  2. Make sure it is connected to CN1 on the printer control board.
  3. It can occur if there are notes already in the transport before the start of a transaction or if the exit sensor is blocked. 1.
  4. It is usually caused by attempting to dispense currency that is unacceptable or currency that has not been properly prepared. 1.
  5. The journal on these machines should be printed on a regular basis (i.e.
  6. Verify that all DC voltages applied to the printer control board are correct.

Verify that main board to electronic journal and the electronic journal to dispenser cables securely seated at both ends of the cable. If it works with the door open, remove obstruction causing the diverter to contact the vault door. 4. If these actions have no effect, replace the dispenser 55 RAM corruption A mechanical failure has occurred. Triton Error Code 101 Test the dispenser by completing several test dispenses. 4.

Verify that the power supply is operating and the DC voltages being supplied to the main board and dispenser are correct. Inspect main board to electronic journal communication cable for damage. Verify clearance at the diverter. https://www.nasatm.com/error_codes/code/33/ Make sure the connectors are seated securely on the main board and on the electronic journal. 4.

Inspect main board to electronic journal communication cable for damage. Triton Traverse Error Code 917 If the error clears, put the cash dispenser in service. 4. If this does not correct the problem, verify that the paper low sensor is correctly attached to the paper bracket and that the cable between the paper low paper feed assembly Your cache administrator is webmaster.

Triton Error Code 244

Once the cause has been resolved, place desired cassettes into service and reset the error. http://speedybuckatm.com/index.php/service-support/atm-error-codes Make sure the connectors are seated securely on the main board and on the electronic journal. 2. Atm Error Codes List If the error persists, possible causes of the problem may be the low paper sensor assembly, the docking station, the main board, or cables. 196 Card reader error 1. Triton Atm Error Code 151 Purge the dispenser using PURGE command.

Fill if needed. weblink Note, if the EJ is connected to the load port of the 9100 main board, permanent damage may result. 2. Reset the Cash Dispenser by turning OFF the AC power switch for a few seconds and switching it back ON. Install the cassette. Triton Error 236

If the test dispenser fails again, try testing while pushing in on the cassette. This page uses frames, but your browser doesn't support them. Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 126 Diverter moved to reject position during dispense Inspect for a note jam at the diverter. navigate here It may be necessary to replace the dispenser. 47 Note missing at double detect This status is generated if the double detect fails to detect a document already seen by the

Do several test dispense operations. 4. Atm Error Codes Hyosung Reset the cash dispenser. Turn the AC power OFF for a few seconds and then back ON to power cycle and reset the cash dispenser. 3.

Seat connectors or replace the power supply as needed. 2.

Reset the cash dispenser. If the cables are undamaged, the main board or electronic journal may be defective 146 No reply from command to electronic journal 1. Verify that there is paper in the printer. Triton Error Code 616 Make sure the electrical connections to the timing wheel sensor are secure and the time wheel sensor is clean.

Make sure the connectors are seated securely on the main board and on the electronic journal. 4. Test the dispensing mechanism by completing several test dispenses. The feed sensors may be dirty. his comment is here If no jam is located, remove the first note from the cassette.

Verify that all DC voltages applied to the printer control board are correct. The cables may be defective. 3. Inspect the cables connected to CN2, CN3, CN4, and CN5. If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly 5 If the cables are undamaged

If there is no visible damage and the connectors are attached to the sensor boards the best course of action is to replace the dispensing mechanism. Home ATM Machines Genmega Onyx Series Onyx W Series G2500 Series GT3000 Series GK1000 Bill Payment G6000 Series Hantle 1700W Series C4000 Series T4000 Series Coin Goat Series Hyosung Halo II Remove the cassette and inspect for jammed currency in the width sensor and at the output of the cassette. Verify clearance at the diverter.

Purge then test dispense. If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly 5. Enter the Management Functions and configure the bill size. 187 Maximum withdrawal not configured Enter the management functions and configure the “multiple amount” parameter. Clear all errors and test the dispenser by completing several test dispenses.

If the cables are undamaged, the main board or electronic journal may be defective 153 Electronic journal mode 1. If the test dispenses are completed normally, and the return code are correct, clear all errors and place the cash dispenser in operation. 5. Clear the error. If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly 5.

Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 111 Diverter timeout Inspect for jammed currency at the diverter. Determine what is causing the cassette to not stay locked in place. 4. Make sure the connectors are seated securely on the main board and on the electronic journal. 4. Make sure the connectors are seated securely on the main board and on the electronic journal. 2.

If it is necessary to check continuity of the cable assembly, refer to the appropriate ATM Service Manual for pin out of the cable assembly. 3. Inspect the printer data cable for damage. Note: Dispenser Status (Click Counts) should be run and available before contacting Tech Support 103 Thickness sensor unstable Enter the diagnostic function and complete the “learn note thickness” command. This status occurs when a note is detected by the exit sensor when it should not have been.